10/6/2009 3:47 PM (in response to guang) Hello bloodwater, as mentionned in the thread the old MGE UPS SYSTEMS products couldn't be managed with the PowerChute softwares.All the small products of MGE UPS SYSTEMS are now sustained by Eaton company. So, you can use the softwares that were used for these products and that are always available (and sustained) in the eaton web pages. You can have a look in this page: powerquality.eaton.com then choose your country and select 'software download' (blue arrow on the right side of the page). Then, choose 'Pulsar series' (first link in the middle). Contoh tes psikotes bank. You should arrive in this page If you need a local solution (means RS232 or USB communication between your computer and these UPSs) and you are using Windows operating system you can download directly this software: For the local solution, don't hesitate to perform a short test even if your product isn't listed in the compatibilty list;-) Supervision should be OK. Shutdown could require a short test: short power failure and power restoration; then very long power outage until shutdown; then power restoration when the UPS is shutoff. Then check a new short power failure that needs to be notified.
MGE UPS SYSTEMS Pulsar Evolution 2200/3000/3000 XL. Page 2 - 34007115EN/AA. 34007115EN/AA - Page 3. The eco-design approach used in product development, recycling of Pulsar Evolution at the end of its service life. Computer running MGE communications software, it is possible to program the.
Introduction Thank you for selecting an MGE UPS SYSTEMS product to protect your electrical equipment. The Pulsar Evolution range has been designed with the utmost care.
We recommend that you take the time to read this manual to take full advantage of the many features of your UPS. MGE UPS SYSTEMS pays great attention to the environmental impact of its products. Measures that have made Pulsar Evolution a reference in environmental protection include: the eco-designapproach used in product development, recycling of Pulsar Evolution at the end of its service life. To discover the entire range of MGE UPS SYSTEMS products and the options available for the Pulsar Evolution range, we invite you to visit our web site at www.mgeups.com or contact your MGE UPS SYSTEMS representative. Presentation 1.1 Overall view........ 7 Tower position........ 7 Rack position........
7 1.2 Back......... 8 1.3 Control panel........ Installation 2.1 Unpacking and parts check.......
10 2.2 Upright installation (tower position)...... 11 2.3 Flat installation (rack position)...... 12 2.4 Connecting the protected equipment...... 13 2.5 Connection to the RS232 or USB communications port (optional)... 14 2.6 Connection to the data-line protection port (optional).... 14 2.7 Installation of the communications-cardoption.....
Operation 3.1 Start-up......... 16 3.2 Shift to booster or fader mode (during voltage variations in the AC-inputpower).. 16 3.3 Operation on battery power (following failure of AC-input power)... 17 Transfer to battery power....... 17 Threshold for the low-batterywarning......
17 3.4 Personalisation (optional)....... 18 Function......... 18 ON / OFF conditions tab....... 18 Battery tab......... 18 Voltage-thresholdstab....... 19 Sensitivity tab........ Maintenance 4.1 Trouble-shooting........
20 4.2 Replacement of the battery module...... Appendices 6.1 Technical data........ 24 Simplified diagram........
24 Technical characteristics....... 25 Examples of battery backup times...... 26 6.2 Glossary......... 27 6.3 Index......... 1 USB communications port. 2 RS232 communications port.
3 Connector for automatic detection of an additional battery module. 4 Data-lineprotection. 5 Slot for communications-cardoption.
6 Connector for an additional battery module. 7 Output circuit breakers. 8 Four outlets for direct connection of protected equipment. 9 Two groups of two programmable outlets (groups 1 and 2). 10 Input circuit-breaker. 11 Socket for connection to AC-powersource. 12 Battery module connectors (to the UPS or to other battery modules).
13 Connectors for automatic detection of additional battery modules. 14 Circuit breaker for battery ON/OFF and protection. Installation 2.1 Unpacking and parts check 24 26 25 27 28 29 30 31 P U L S A R Evolution 3 0 0 0 32 24 Cord for connection to the AC-powersource for 3000/3000 XL versions only (for the 2200 version, use the power cord of the protected equipment). 25 Two cords for connection of the protected equipment. 26 RS232 communications cable. 27 USB communications cable. 28 Telescopic rails for mounting in 19' bay with mounting hardware.